Euro slot punch in two sizes. The 32mm euro slot punch is the standard size for the UK and Europe, while the 25mm euro slot punch is used internationally. Read more about the individual euro slot punches below: 25mm Euro Slot Punch. Variations in the individual panel dimensions, as measured scoreline to scoreline on the finished blank when measured in the flat (as a scored and slotted sheet), shall not exceed ± 1/16' (approx. 1.5 mm), and variation in the overall dimensions shall not exceed ± 1/8' (approx.

Standard Euro Slot Dimensions Calculator
Standard Euro Slot Dimensions Chart
Standard Euro Slot Size
Standard Euro Slot Dimensions Comparison

EN10025(1-6) Brief Introduction:
EN 10025 includes a series of European standards for structural steel products, delivery condition is specified as hot rolled. For example, hot rolled steel coils, hot rolled steel section. EN 10025 standard (6 parts) covers a wide range of structural steel product.

EN 10025-1:2004General technical delivery conditions.

Nominal Slot Size vs available Tool Bit Sizes. The defined tolerances start with the tool bit size, these are available in standard size steps of 0.05mm. Any slot defined that does not meet this 0.05mm steps will be rounded to the nearest step. It is possible to have smaller tool bit size steps but the cost far outweighs any reason to do so. Length is either 160mm or 340mm (Norm) Height is given in 'U' 1U = 43.60mm, Length is given in 'mm', Width is given in 'T' or HP 1HP = 5.08mm HP: Horizontal Pitch; Card sizes listed below are one slot or 6T wide A size CCA dimensions = 3U x 160mm. Craps buying numbers. A 3U Printed Wiring Board PWB is 100mm high. When international shipping palletized freight, it's an advantage for you to pack on standard pallet sizes and to follow stacking guidelines. While it's true that we can move a range of non-standard pallet sizes, forklifts and their operators work best when they can gain certain, standardized clearance moving packages.

EN 10025-2:2004Technical delivery conditions for non-alloy structural steel products.

S Structural steel.
E Engineering steel.
235 Minimum yield strength (Reh) in MPa at 16mm
JR Longitudinal Charpy V-notch impacts 27 J at + 20°C
J0 Longitudinal Charpy V-notch impacts 27 J at 0°C
J2 Longitudinal Charpy V-notch impacts 27 J at - 20°C
K2 Longitudinal Charpy V-notch impacts 40 J at - 20°C
+AR Supply in as rolled conditions
+N Supply in normalized/normalized rolled conditions

Customer options.

C Grade suitable for cold forming
Z Grade with improved properties perpendicular to the surface.

For example: S275JR+AR, S355J2C+N EN 10025-3:2004Technical delivery conditions for normalized/normalized rolled weldable fine grain structural steel products.

S Structural steel.
275 Minimum yield strength (Reh) in MPa at 16mm
N Longitudinal Charpy V-notch impacts temp. not lower than -20°C
NL Longitudinal Charpy V-notch impacts temp. not lower than -50°C

Customer options.

Z Grade with improved properties perpendicular to the surface.

For example S275N, S275NL

EN 10025-4:2004Technical delivery conditions for thermo mechanical rolled weldable fine grain structural steel products.

S Structural steel.
275 Minimum yield strength (Reh) in MPa reference to 16mm
M Longitudinal Charpy V-notch impacts temp. not lower than -20°C
ML Longitudinal Charpy V-notch impacts temp. not lower than -50°C

Customer options.

Z Grade with improved properties perpendicular to the surface.

For example S355M, S355ML Slot

EN 10025-5:2004Technical delivery conditions for structural steel products with improved atmospheric corrosion resistance.

S Structural steel.
355 Minimum yield strength (Reh) in MPa at to 16mm
J0 Longitudinal Charpy V-notch impacts 27 J at 0°C
J2 Longitudinal Charpy V-notch impacts 27 J at - 20°C
K2 Longitudinal Charpy V-notch impacts 40 J at - 20°C
W Improved atmospheric corrosion resistance
P Greater phosphorus content (grade 355 only)
+AR Supply in as rolled conditions
+N Supply in normalized/normalized rolled condition

Standard Euro Slot Dimensions Calculator

Customer options.

Z Grade with improved properties perpendicular to the surface.

Standard Euro Slot Dimensions Chart

For example S235J0W+AR, S355J2W+N

EN 10025-6:2004Technical delivery conditions for steel plate and sheet of high yield strength structural steel products in the quenched and tempered condition.

S Structural steel.
460 Minimum yield strength (Reh) in MPa at 16mm
Q Longitudinal Charpy V-notch impacts temp. not lower than -20°C
QL Longitudinal Charpy V-notch impacts temp. not lower than -40°C
QL1 Longitudinal Charpy V-notch impacts temp. not lower than -60°C

Customer options.

Z Grade with improved properties perpendicular to the surface.

Standard Euro Slot Size

For example S460Q, S690QL

Standard Euro Slot Dimensions Comparison

History of EN 10025(1-6):
Written by European Committee for Iron and Steel Standardisation, which is a department working on European Standards for structural steel product.
First version of EN 10025 was released in UK by BSI (British Standards Institute)- EN 10025 : 1990, European Standards (ENs) for structural steel products. The first version of this standard is named EN 10025-1990, it replaced part of of BS4360:1986; the second version of EN 10025 was released in 1993, EN 10113 : parts 1, 2 & 3 and EN 10155 was made together. In the summer of 1994, EN10210: part 1 was released and BS 4360 was invalid officially. In 2008 EN 10025 standards replaced SANS 1431 as the newest EN version.